• SKAA / SKAA Pro dual-mode transmitter featuring two balanced analog audio inputs and Burr-Brown input buffers and converters
• Designed specifically for sending audio wirelessly from pro audio gear to SKAA speakers, SKAA headphones, and other SKAA receivers
• Ideal for wirelessly connecting your analog or digital live sound mixer to front-of-house speakers, floor wedges, and headphones
• Perfect for wirelessly connecting your DJ mixer/deck to your main speakers and/or your cue mix headphones (for example Dillinger Helix headphones)
• Ideal for sending out wireless cue mixes from your DAW or mixing desk to your live room — to talent wearing Helix headphones, for example
• Flip a switch and Dani works with consumer audio devices — transmit audio from any phone, tablet, iPad, computer, camera, music player — literally any device with a headphone jack or an audio line output

Part# PL5580/A0520

Specifications

• 14 hour run time from a full charge using its internal rechargeable Li-Ion battery
• Feed 4 SKAA speakers or headphones in SKAA mode (at 36ms latency)
• Feed 2 SKAA speakers or headphones in SKAA Pro mode (at 19ms latency) … great for lightning-fast scratching and finger drumming
• Two 1/4" TRS balanced/unbalanced line-level inputs with input impedance > 10k ohms
• Inputs 1 and 2 can be used for Left / Right audio or to carry separate signals (eg. FRONT OF HOUSE on 1 and CUE MIX on 2)
• Got XLR balanced outputs on your DJ Controller?  Perfect.  Just use two XLR-F to 1/4” TRS balanced cables to connect it to Dani
• Legendary Burr-Brown input buffers
• Legendary Burr-Brown analog to digital converters
• Global volume control for all downstream devices.  Dani doesn’t scale your audio prior to wireless transmission — instead it remote controls the gain in the amplifiers in the downstream devices, delivering the best signal-to-noise ratio possible at all volume levels.
• Mute/unmute control for all downstream devices
• Thru jacks wired in parallel with the inputs so you can flow your signal to the next destination in addition to transmitting it out wirelessly by SKAA or SKAA Pro
• Thrus are great for a hybrid system in which there are wired speakers in the front of the room and wireless speakers in the back of the room.  The output of your deck connects to Inputs 1/2.  Thrus 1/2 then feed your amps.
• Thrus also enable you to run 2 Dani transmitters at the same time to double your wireless speakers at a gig.  Connect your mixer out to Dani A's Inputs.  Then connect Dani A's thrus to Dani B's inputs using two TRS balanced patch cables.
• Dani can handle a wide range of line-level signals from the wimpy to the extreme.  Feed Dani from a meager headphone jack (3.5 mm phone or computer source) or hit it with +22 dBu of XLR balanced signal from the hottest DJ mixer.
• Li-Ion battery is user-replaceable so your Dani won’t become a useless brick in the future
• Dani charges from any USB power source (virtually any USB phone charger with a Type A jack will work) — use the included Type A to Type C cable to connect it to the Type C charging port on Dani’s rear panel
• Fast charging is supported when a 2A (or better) capable USB power adapter is used
• Dani can transmit and charge via USB at the same time
• Fuel gauge tells you how much battery life is remaining — the last bar will start to slow flash when 45 min battery life remains
• Auto powers off when the battery reaches empty
• Up to 50-meter reliable indoor range with the included +2 dBi antenna (note that actual range will depend also on the antenna implementation in the receive-side device)

Links

• For how-to Youtube videos, please subscribe to our channel click here
• For more information on Dillinger Labs, click here
• For product use diagrams, check out the Dani Owner's Manual

• SKAA/SKAA Pro dual-mode Receiver
• Boasts 50-meter range, Burr-Brown DACs, balanced/unbalanced line-level outputs, and Headphone jacks
• Pro-grade SKAA wireless audio.  100% Bluetooth-free.  100% WiFi free.
• The perfect companion to the Dani SKAA/SKAA Pro Transmitter
• Works with all SKAA Transmitters, all SKAA Pro Transmitters, and all SKAA Nadja Hubs
• Designed specifically to upgrade virtually any piece of sink-side pro audio gear to SKAA/SKAA Pro wireless
• Perfect for upgrading your amplifiers, powered speakers, and wired headphones to lightning-fast SKAA wireless
• Pair with a Dani transmitter to replace long XLR or TRS cable runs
• Receives two discrete audio channels and outputs them on four ¼″ jacks (2 output jacks per audio channel)

Part# PL5581 

What Can It Do?

• Need to add an extra pair of monitor speakers to the “band room” in your studio?  Upgrade a pair of Focal, Dynaudio, Adam, Genelec, KRK, or Yamaha powered monitors with a single Streetheart to fill that remote room with low-latency audio from your control room.
• Love your Mackie, JBL, EV, Alto or QSC powered PA speakers?  Great — convert them to lightning-fast SKAA wireless by adding Streetheart.
• Love your Soundboks Gen 3 speakers (with SKAA built in) but want to add SKAA wireless capability to your older Soundboks Gen 2 speakers?  Just add a Streetheart to those Gen 2s.
• Want to add a battery-operated wireless subwoofer to your Soundboks network?  Convert a powered sub into a SKAA wireless sub just by adding Streetheart.
• Use the level control knob to turn down the blistering output of Streetheart and you can feed consumer-grade gear like bookshelf speakers or your home theatre system.
• Feed up to 4 Streetheart Receivers from any SKAA Transmitter (at 36 ms latency) … this is the best general-purpose mode
• Feed up to 2 Streetheart Receivers from any SKAA Pro Transmitter (at 19 ms latency) … great for singing, guitar playing, lightning fast scratching and finger drumming
• Outputs 1 and 2 can be used for Left / Right audio, or, to handle  two completely unrelated signals (for example, FRONT OF HOUSE on Out 1 and FLOOR MONITORS on Out 2)
• Got XLR balanced line-level inputs on your amps or powered speakers?  Perfect.  Just use two ¼″ TRS to XLR-M balanced cables to feed your gear from Streetheart.
• Want to use unbalanced TS cables?  No problem, just plug into Lower Outs 1 & 2 ¼″ jacks which support both balanced and unbalanced line-level connections.
• Pad switch lets you reduce the output on Upper Out 1 by 6 dB or 12 dB just in case you need to feed a device with a reduced signal level
• When using Headphone Outs, the person plugged into Headphone Out 1 can opt to listen quieter by engaging the Pad
• Change Outs 1 & 2 to Headphone jacks by engaging the Headphone Switch (meanwhile the Lower Outs 1 & 2 remain bonafide pro-level balanced line outs)
• Set the Pad to -12 dB and plug your Headphones into Out 1 to check your incoming audio before powering on your connected amps / speakers
• Headphone outs make a perfect live room headphone cue mix setup
• Perfect for creating a wireless Headphone cue mix system for your studio
• Engage the Split Switch to listen to program 1 audio only on Headphone 1 and program 2 audio only on Headphone 2 — that’s two separate headphone cue mixes from a single Streetheart !  Need four separate cue mixes?  Just use two Streethearts.
• Supports SKAA Differential mode Transmitters such as the Valerie Mk2 microphone and Jacqueline guitar Transmitter

Specifications

• Four ¼″ TRS balanced line-level outputs
• Up to 50-meter reliable indoor range with the included +2 dBi antenna (note that your actual range will depend also on the antenna implementation in the transmit-side device)
• Legendary Burr-Brown digital to analog converters — nothing but the best
• Proper +16 dBu output levels to ensure you can get the max wattage from your connected gear
• Feed signal-hungry 19” rack amplifiers (any brand) — feed up to 4 separate amplifiers from a single Streetheart Receiver
• Feed up to two pairs of headphones
• Works with all headphones having 32 ohms impedance or higher
• 30-step local Volume control for all four outputs
• Local Mute control for all four outputs
• 12 hour run time from a full charge using Streetheart's internal rechargeable Li-Ion battery
• Streetheart’s 18650 Li-Ion battery is user-replaceable so your Streetheart won’t become a useless brick in the future
• Streetheart charges from any USB power source (virtually any USB phone charger with a Type A jack will work) — use the included Type A to Type C cable to connect your charger to the Type C charging port on Streetheart’s User Panel
• Streetheart can receive and charge via USB at the same time
• Fast charging is supported when a 2A (or better) capable USB power adapter is used
• Fuel gauge tells you how much battery life remains — last bar will start to slow flash when you’ve got 45 minutes left
• Auto powers off when the battery reaches empty
• SKAA Bond Button and Bond Indicator enable all of SKAA’s Bonding functions — they enable you to select any SKAA Transmitter you wish to listen to, and, to remember up to 10 Favourite Transmitters in Streetheart’s Green List.  Download the complete SKAA Receiver User’s Guide from https://www.skaastore.com/pages/tlc

Links

• For how-to Youtube videos, please subscribe to our channel click here
• For more information on Dillinger Labs, click here
• For product use diagrams, check out the Streetheart Owner's Manual

• High-quality SKAA wireless musicians' headphones — if these are not the best wireless headphones you’ve ever owned, return them to us within 30 days for your money back!
• Designed to meet the stringent requirements of pro musicians as well as hundreds of other use cases
• Adjustable headband for listener comfort
• Great for long listening sessions such as flights and commutes
• High-quality ear cups effectively keep out external noise
• Stunning black and red design
• Volume control +/- buttons
• Track control:  Play/Pause, Next Track and Previous Track supported via Power button click commands (1, 2 and 3 clicks)
• SKAA Bond Button and Indicator
• Built for Dillinger Labs by top Japanese headphone brand
• Use up to 4 SKAA receivers (any combination of Helix headphones and any  other SKAA receivers) at the same time with any one SKAA transmitter
• Works with SKAA Nadja hubs —for example listen to FM or Bluetooth or AUX audio from the Ryobi Score Primary speaker (available at Home Depot)
• Remembers up to 10 of your favourite transmitters (and/or Nadja Hubs)
• No pairing —instead use the Bond Button for easy single-sided bonding (selecting the transmitter you want to hear audio from)

Part# PL5576/A0338

Specifications

• 25-meter indoor range when used with Ursula, Akiko, and Talisa SKAA transmitters as well as Nadja Hubs
• 15 meter indoor range when used with Diz, Gemma and Cassandra transmitters
• Low latency —great for watching movies, TV, playing games and even playing musical instruments (eg. Using apps such as GarageBand or AmpKit+)
• 10-hour battery life with typical use
• Automatically powers off when not in use to save battery
• Charges from any USB power source via Micro USB connection using common USB cables and adapters
• Works with SKAA cmd (optional app) when used with Ursula, Diz, Izabella, Gemma as well as the new Casandra and Serena SKAA transmitters
• Ships with SKAA OS 2.5 - use up to two receivers at 19ms of latency, or up to 4 receivers at 36ms of latency. Works with all transmitters running SKAA OS 2.1 or newer (if you’re not sure what version you have, go to TLC, send us a note and just ask)

Links

• For how-to Youtube videos, please subscribe to our channel here
• For more information on Dillinger Labs, click here
• Download the Helix Manual here